:: Neutronic manufacturing co ::

APFCR – TYPE 1301.	APFCR – TYPE 144.
MICROPROCESSOR APFCR – 1304 & 1305

CONTROLS

BasicPowerFactor: The value at which that power factor is to be
set is selected by means of this control, which has a calibrated dial
from0.81agto 1.00.
DeadBand:Dependinguponthe KVARcapacityofeach capacitorto
be switched the, relay response sensitivityhas to be adjusted. The
dead band control serves to adjust this, so that hunting isavoided
DeadBandControl: . AtMinimum-::'::3° Electrical
AtMaximum- ::'::13°Electrical

SPECIFICATION

Voltage: 400 or 415 or 440V 3 Ph. 3. wire, 50 Hz, 2.5 VA(J ]OVAC.
forHTapplication).
Current: Through 5 Amp. CTsecondary on RPhase of incomer.3VA
(1Amp model on request).
Output: Each capacitor control relay is provided with one change
over contaa rated formaximum 230VAC/5Amps.resistive
load.
P.FA. djustment range: 0.81agto 1.00.
P.F. Meter range: 0.61agto 0.6Iead.

APFCR – TYPE 1301.

Product Description :

Digital automatic control relay for intelligent control of capacitor bank.
Simple Commissioning: By automatic identificaton of threshold current(c/k value), phase angle, connected capacitor stages and switching sequences.
Operator Overview: Through clear display of key momentary values and operating parameter.
a. Power factor (cos Ø)
b. Apparent (RMS), active and reactive currents
c. 5th, 7th ,11th ,13th harmonic voltage content
d. Total Capacitive power required to meet target power factor setting

Monitoring of Harmonic Levels: By continuous monitoring and display of harmonic voltage levels. In the event of harmonic levels exceeding programmable limits, all capacitors will be switched off through over-current alarm.

Additional Protection for Capacitors: The RMS current monitoring function provides excellent protection for capacitor bank without harmonic filters, especially when resonance
cause an increase in harmonic levels.

	Potential-free alarm contact.

	Programmable overcurrent alarm threshold limit(from 1.05 to 3.0 x Irms).

	Continuous monitoring for defective capacitor stages through self adjustment of control program.

	Zero voltage and zero current tripping with alarm signal.

	Kinked" control curve characteristics avoid overcompensation under light load.

	Four-quadrant power control with LED display when active power is generated into mains.

	Manual/automatic operation with ability to switch each individual capacitor stage ON or OFF.

	Target power factor setting adjustable from 0.80 inductive to 0.95 capacitive in steps of 0.01.

	Preset up to three fixed capacitor stages which will be excluded from normal automatic operation.

	Independent setting of capacitor swithcing time to match discharge time of capacitor stages.

	Suitable for current transformers with rated secondary current of 1A-5A.

Alarm Signals for:

a. Undercompensation
b. High harmonic levels
c. Overcurrent
d. Switching counters
e. Fault in voltage circuit (U = 0 alarm)
f. Fault in current circuit (I = 0 alarm)
g. Fault in capacitor stages (C = 0 alarm)

PF Target Power Factor (1.70 to 1.00)

PF Cap / Ind : Lagging /Leading Target Power Factor.

Dead band : Dead band for target Power Factor (0.00 t0 0.30).

Corr. Delay : Capacitor - switching delay (1 to 250).

Ct Rating 1A / 5A : Current rating for the current transformer/ (select 1 AMP if the CT input is received through the select 5Amp if the CT input is received through the R5 pin of the power connector).

Ct Ratio : turns ratio for the current transformer (1 to 200)

Program No : Program No. ( 1 to 33) (refer the program no. chart).

CB1 KVAr : KVAr rating of the first Capacitor Bank connected (0.5 to 99.5 KVAr)

Top

APFCR – TYPE 144.

Built in analog / digital P. F. meters
Calibrated setting dial
Dead band setting
Built in auto/ manual switching
Cycle switching
Indicating leds for each capacitor switching modules
A uniquetiming action that follows the charge /discharge of the controlled capacitor
Fully solid state reliability.

Top

MICROPROCESSOR APFCR – 1304 & 1305

General :

Power Factor is an important Electrical parameter needing control,State of theart microcontrolbased APFCR type 130 5is specially designed to control the powerfactor of aninstallation by giving signals to switch capacitors on and of in a FIFO/FILOmanner accordinglyandreliably. The controller is ~ousedin a COQ1pac Ftlush Panelmounting enclosure of size144x 144DIN and has all the required controls and indications arranged on the front panel. High barrier /
shroud edterminals are provided attherear of the casefor external connections. Solid state comonents are used through out with the exception of the electromechanical relays for the externals witch in gfor high reliability and compactness.The constructionis rugged, designed for years of troublefree service.

Features

Micro control Field proven design.
- Available in 4, 8, 12,16,stages.
- Accurate measurement & user Friendly operation
- Built in Auto/ Manual control.
- Calibrated PF setting & deadband.
- Built in digital timer for fast operation ensures capacitor safety.
- Built in self/test facility.
- Auto detection for low current & external wrong connection indicatonon
- Control power factordirectlyregardlessofsizeofcapacitor.
- Low current cut off at1%.
- Choice of sequence FIFO/FILO/Bina(ray.nyone)
- Available for LT & HT application.
- Compact DIN std flush mounting144mmx144mmx 1OOmm depth